Installation
|
Identify the tools required for installation pictured below.
Step 2
Determine the type of application (flush or corner, see step 3 for details) and framing requirements.
If installing SCREENEZE® in temperatures under 60 degrees, see Cold Weather Instructions in the forms tab.
Click the button below for framing options
If installing SCREENEZE® in temperatures under 60 degrees, see Cold Weather Instructions in the forms tab.
Click the button below for framing options
Step 3
Step 4
Measure the opening and cut as required. Be sure Vinyl Cap does not move on the Aluminum Base Channel while making miter cuts.
CUTTING TIP: Use a 10" miter saw with a 200 tooth plywood blade. We also recommend the Freud Diablo series of non-ferrous/plastic blades; specifically the 10" 80 tooth blade or the 12" 96 tooth blade. You can also use a hack saw with a fine tooth metal cutting blade.
TIP: Never force SCREENEZE® into an opening. For best results, make cuts snug or short by a 1/32" - 1/16" to allow for expansion and contraction.
TIP: Pencil identifying marks on the corresponding Vinyl Cap and its Aluminum Base Channel so they are easily placed and kept together when completing steps 6 thru 10.
CUTTING TIP: Use a 10" miter saw with a 200 tooth plywood blade. We also recommend the Freud Diablo series of non-ferrous/plastic blades; specifically the 10" 80 tooth blade or the 12" 96 tooth blade. You can also use a hack saw with a fine tooth metal cutting blade.
TIP: Never force SCREENEZE® into an opening. For best results, make cuts snug or short by a 1/32" - 1/16" to allow for expansion and contraction.
TIP: Pencil identifying marks on the corresponding Vinyl Cap and its Aluminum Base Channel so they are easily placed and kept together when completing steps 6 thru 10.
Step 5
Find the center of each cut piece. Then mark for screw location at 10" - 12" O.C. from and including the center mark. Always screw at 2" from either end of cut piece. Adjust your centers to the 2" distance from the end of the cut piece.
TIP: Although we provide a self-tapping screw, we recommend pre-punching or drilling a 3/16" hole at you marked centers.
TIP: Although we provide a self-tapping screw, we recommend pre-punching or drilling a 3/16" hole at you marked centers.
Step 6
Step 7
Remove Vinyl Cap from Aluminum Base Channel. A 5-in-1 tool, a miniature "Wonder Bar", or a small straight screwdriver may be used. Be careful not to scar the Aluminum Base Channel or Vinyl Cap during this process. Be careful not to mix-up the pieces as they might be different lengths.
TIP: After loosening the ends gently pull the Vinyl Cap off of the Aluminum Base Channel.
TIP: After loosening the ends gently pull the Vinyl Cap off of the Aluminum Base Channel.
Step 8
To install screen; hold fabric to the top (always first) of the opening. Square fabric on top of the opening. Then attach screen to Aluminum Base Channel by pressing or tapping the vinyl cap onto the corner. Secure the first 2" - 3" of your corner by seating the Vinyl Cap to the Aluminum Base Channel with a rubber hammer. Then proceed to the center of the cap to seat it completely. Make sure the screen has remained square on the frame. Complete the Vinyl Cap installation by tapping from the center out towards the corners. Be sure the Vinyl Cap is secure against the Aluminum Base Channel before proceeding.
TIP: If it's a windy day place a thumbtack on each corner. Leave the screen on the roll, this helps to keep it square and not blow around.
TIP: If it's a windy day place a thumbtack on each corner. Leave the screen on the roll, this helps to keep it square and not blow around.
Step 9
Install the Vinyl Cap on the bottom (always second) of the opening in the same manner used in step 8.
TIP: Do not stretch the screen fabric. SCREENEZE® will uniformly stretch the screen for you. Let screen drape over bottom channel and position screen so there are no wrinkles left or right. Secure Vinyl Cap as described in step 8.
TIP: Do not stretch the screen fabric. SCREENEZE® will uniformly stretch the screen for you. Let screen drape over bottom channel and position screen so there are no wrinkles left or right. Secure Vinyl Cap as described in step 8.
Step 10
Install side pieces as described in step 8. Check the entire installation ensuring that the Vinyl Cap is completely seated on the Aluminum Base Channel. Use a razor knife to cut away excess screen fabric.
TIP: use the base of the Vinyl Cap, holding your knife at a perpendicular angle, as a guide for trimming the screen.
TIP: use the base of the Vinyl Cap, holding your knife at a perpendicular angle, as a guide for trimming the screen.